Release Notes

We want you to know what you’re getting when you download software from CEI. That’s why our release notes and documentation are openly available on our website. We work hard to give our customers the best experience we can and we’re proud of the work we do, warts and all.

lines of code on a blue background

DesignCalcs

DesignCalcs version 2017.0

Apr 21, 2017

New Features

  • Studded Outlet calculations will now take advantage of the seamless equivalent feature if applicable. The 2015 Edition of the code introduced this in the UG-37 reinforcement calculations. For 2015 and newer vessels, the studded outlet material and the host material will both determine if they need a seamless equivalent (this applies to welded product forms that have a built in 85% joint efficiency for their allowable stress). 
    If the material needs a seamless equivalent, DesignCalcs will attempt to find one based on a matching protocol - see Seamless Equivalent Criteria. If a seamless equivalent is found, the reinforcement math will use the allowable stress from the seamless equivalent. If a seamless equivalent could not be found, the allowable stress will instead be divided by 0.85. This code change favors a more economical design.  DC-437

Issues Resolved

  • An issue was resolved that was preventing all of the Temerature/Ultimate Strength pairs from showing in the material viewer.  DC-484
  • An issue was resolved that was causing errors to be thrown during nozzle report creation for nozzles that were using custom materials and had lost connection to the custom material.  DC-575
  • An issue was resolved that was causing the extreme fiber elongation calculations from showing the head forms.  The may update the status on some heads.  DC-535
  • Removed an outdated reference to UG-45(c) in the nozzle form under Unit Stresses on the Weld Paths tab and also in the nozzle report under the same section.  The reference was repaced with just UG-45.  DC-579
  • An issue was resolved that would cause an exception to occur if a WRC analysis was copied several times after WRC reports were run.  DC-516
  • An issue was resolved that was preventing the correct status from showing up in certain cases for heads that triggered the Appendix 1-4(f) calculations.  DC-481
  • Fixed some issues with the head copy to prevent multiple "left", "right", "top", or "bottom" heads to exist.  DC-804, DC-806

Miscellaneous

  • Several improvements have been made to the online knowledge base
  • The copyright was updated to 2017.  DC-763

DesignCalcs version 2017.0

Apr 21, 2017

New Features

  • Studded Outlet calculations will now take advantage of the seamless equivalent feature if applicable. The 2015 Edition of the code introduced this in the UG-37 reinforcement calculations. For 2015 and newer vessels, the studded outlet material and the host material will both determine if they need a seamless equivalent (this applies to welded product forms that have a built in 85% joint efficiency for their allowable stress). 
    If the material needs a seamless equivalent, DesignCalcs will attempt to find one based on a matching protocol - see Seamless Equivalent Criteria. If a seamless equivalent is found, the reinforcement math will use the allowable stress from the seamless equivalent. If a seamless equivalent could not be found, the allowable stress will instead be divided by 0.85. This code change favors a more economical design.  DC-437

Issues Resolved

  • An issue was resolved that was preventing all of the Temerature/Ultimate Strength pairs from showing in the material viewer.  DC-484
  • An issue was resolved that was causing errors to be thrown during nozzle report creation for nozzles that were using custom materials and had lost connection to the custom material.  DC-575
  • An issue was resolved that was causing the extreme fiber elongation calculations from showing the head forms.  The may update the status on some heads.  DC-535
  • Removed an outdated reference to UG-45(c) in the nozzle form under Unit Stresses on the Weld Paths tab and also in the nozzle report under the same section.  The reference was repaced with just UG-45.  DC-579
  • An issue was resolved that would cause an exception to occur if a WRC analysis was copied several times after WRC reports were run.  DC-516
  • An issue was resolved that was preventing the correct status from showing up in certain cases for heads that triggered the Appendix 1-4(f) calculations.  DC-481
  • Fixed some issues with the head copy to prevent multiple "left", "right", "top", or "bottom" heads to exist.  DC-804, DC-806

Miscellaneous

  • Several improvements have been made to the online knowledge base
  • The copyright was updated to 2017.  DC-763

DesignCalcs version 2017.0

Apr 21, 2017

New Features

  • Studded Outlet calculations will now take advantage of the seamless equivalent feature if applicable. The 2015 Edition of the code introduced this in the UG-37 reinforcement calculations. For 2015 and newer vessels, the studded outlet material and the host material will both determine if they need a seamless equivalent (this applies to welded product forms that have a built in 85% joint efficiency for their allowable stress). 
    If the material needs a seamless equivalent, DesignCalcs will attempt to find one based on a matching protocol - see Seamless Equivalent Criteria. If a seamless equivalent is found, the reinforcement math will use the allowable stress from the seamless equivalent. If a seamless equivalent could not be found, the allowable stress will instead be divided by 0.85. This code change favors a more economical design.  DC-437

Issues Resolved

  • An issue was resolved that was preventing all of the Temerature/Ultimate Strength pairs from showing in the material viewer.  DC-484
  • An issue was resolved that was causing errors to be thrown during nozzle report creation for nozzles that were using custom materials and had lost connection to the custom material.  DC-575
  • An issue was resolved that was causing the extreme fiber elongation calculations from showing the head forms.  The may update the status on some heads.  DC-535
  • Removed an outdated reference to UG-45(c) in the nozzle form under Unit Stresses on the Weld Paths tab and also in the nozzle report under the same section.  The reference was repaced with just UG-45.  DC-579
  • An issue was resolved that would cause an exception to occur if a WRC analysis was copied several times after WRC reports were run.  DC-516
  • An issue was resolved that was preventing the correct status from showing up in certain cases for heads that triggered the Appendix 1-4(f) calculations.  DC-481
  • Fixed some issues with the head copy to prevent multiple "left", "right", "top", or "bottom" heads to exist.  DC-804, DC-806

Miscellaneous

  • Several improvements have been made to the online knowledge base
  • The copyright was updated to 2017.  DC-763

DesignCalcs version 2017.0

Apr 21, 2017

New Features

  • Studded Outlet calculations will now take advantage of the seamless equivalent feature if applicable. The 2015 Edition of the code introduced this in the UG-37 reinforcement calculations. For 2015 and newer vessels, the studded outlet material and the host material will both determine if they need a seamless equivalent (this applies to welded product forms that have a built in 85% joint efficiency for their allowable stress). 
    If the material needs a seamless equivalent, DesignCalcs will attempt to find one based on a matching protocol - see Seamless Equivalent Criteria. If a seamless equivalent is found, the reinforcement math will use the allowable stress from the seamless equivalent. If a seamless equivalent could not be found, the allowable stress will instead be divided by 0.85. This code change favors a more economical design.  DC-437

Issues Resolved

  • An issue was resolved that was preventing all of the Temerature/Ultimate Strength pairs from showing in the material viewer.  DC-484
  • An issue was resolved that was causing errors to be thrown during nozzle report creation for nozzles that were using custom materials and had lost connection to the custom material.  DC-575
  • An issue was resolved that was causing the extreme fiber elongation calculations from showing the head forms.  The may update the status on some heads.  DC-535
  • Removed an outdated reference to UG-45(c) in the nozzle form under Unit Stresses on the Weld Paths tab and also in the nozzle report under the same section.  The reference was repaced with just UG-45.  DC-579
  • An issue was resolved that would cause an exception to occur if a WRC analysis was copied several times after WRC reports were run.  DC-516
  • An issue was resolved that was preventing the correct status from showing up in certain cases for heads that triggered the Appendix 1-4(f) calculations.  DC-481
  • Fixed some issues with the head copy to prevent multiple "left", "right", "top", or "bottom" heads to exist.  DC-804, DC-806

Miscellaneous

  • Several improvements have been made to the online knowledge base
  • The copyright was updated to 2017.  DC-763

DesignCalcs version 2017.0

Apr 21, 2017

New Features

  • Studded Outlet calculations will now take advantage of the seamless equivalent feature if applicable. The 2015 Edition of the code introduced this in the UG-37 reinforcement calculations. For 2015 and newer vessels, the studded outlet material and the host material will both determine if they need a seamless equivalent (this applies to welded product forms that have a built in 85% joint efficiency for their allowable stress). 
    If the material needs a seamless equivalent, DesignCalcs will attempt to find one based on a matching protocol - see Seamless Equivalent Criteria. If a seamless equivalent is found, the reinforcement math will use the allowable stress from the seamless equivalent. If a seamless equivalent could not be found, the allowable stress will instead be divided by 0.85. This code change favors a more economical design.  DC-437

Issues Resolved

  • An issue was resolved that was preventing all of the Temerature/Ultimate Strength pairs from showing in the material viewer.  DC-484
  • An issue was resolved that was causing errors to be thrown during nozzle report creation for nozzles that were using custom materials and had lost connection to the custom material.  DC-575
  • An issue was resolved that was causing the extreme fiber elongation calculations from showing the head forms.  The may update the status on some heads.  DC-535
  • Removed an outdated reference to UG-45(c) in the nozzle form under Unit Stresses on the Weld Paths tab and also in the nozzle report under the same section.  The reference was repaced with just UG-45.  DC-579
  • An issue was resolved that would cause an exception to occur if a WRC analysis was copied several times after WRC reports were run.  DC-516
  • An issue was resolved that was preventing the correct status from showing up in certain cases for heads that triggered the Appendix 1-4(f) calculations.  DC-481
  • Fixed some issues with the head copy to prevent multiple "left", "right", "top", or "bottom" heads to exist.  DC-804, DC-806

Miscellaneous

  • Several improvements have been made to the online knowledge base
  • The copyright was updated to 2017.  DC-763

DesignCalcs version 2017.0

Apr 21, 2017

New Features

  • Studded Outlet calculations will now take advantage of the seamless equivalent feature if applicable. The 2015 Edition of the code introduced this in the UG-37 reinforcement calculations. For 2015 and newer vessels, the studded outlet material and the host material will both determine if they need a seamless equivalent (this applies to welded product forms that have a built in 85% joint efficiency for their allowable stress). 
    If the material needs a seamless equivalent, DesignCalcs will attempt to find one based on a matching protocol - see Seamless Equivalent Criteria. If a seamless equivalent is found, the reinforcement math will use the allowable stress from the seamless equivalent. If a seamless equivalent could not be found, the allowable stress will instead be divided by 0.85. This code change favors a more economical design.  DC-437

Issues Resolved

  • An issue was resolved that was preventing all of the Temerature/Ultimate Strength pairs from showing in the material viewer.  DC-484
  • An issue was resolved that was causing errors to be thrown during nozzle report creation for nozzles that were using custom materials and had lost connection to the custom material.  DC-575
  • An issue was resolved that was causing the extreme fiber elongation calculations from showing the head forms.  The may update the status on some heads.  DC-535
  • Removed an outdated reference to UG-45(c) in the nozzle form under Unit Stresses on the Weld Paths tab and also in the nozzle report under the same section.  The reference was repaced with just UG-45.  DC-579
  • An issue was resolved that would cause an exception to occur if a WRC analysis was copied several times after WRC reports were run.  DC-516
  • An issue was resolved that was preventing the correct status from showing up in certain cases for heads that triggered the Appendix 1-4(f) calculations.  DC-481
  • Fixed some issues with the head copy to prevent multiple "left", "right", "top", or "bottom" heads to exist.  DC-804, DC-806

Miscellaneous

  • Several improvements have been made to the online knowledge base
  • The copyright was updated to 2017.  DC-763